Therma-Tru Impact Garage Doors Nationwide

Therma-Tru Impact Garage Doors: The San Antonio Owner’s Guide

We stock and install Therma-Tru impact-rated garage doors in San Antonio, with most complete door replacements running between $2,800 and $6,400 installed depending on size, insulation level, and finish. If you’re dealing with a failed panel, damaged track, or a door that won’t seal after a storm, we can usually get a technician out within 48 hours for assessment. Most San Antonio homeowners discover the problem the hard way: a hailstorm punches through a non-impact panel, the spring snaps on a Monday morning, or the bottom seal starts letting in June humidity and dust.

Call (903) 488-7019

Therma-Tru impact garage doors are built differently than standard doors. The impact-rated versions use reinforced steel or composite skins laminated over a structural core, and they’re tested to withstand wind-borne debris at specific pressure ratings. The San Antonio market sees two failure patterns most often: rust at the bottom rail from our clay-heavy soil splash-back, and spring fatigue from the temperature swings between our winter nights and triple-digit summer afternoons. Both are fixable, and both are cheaper to address before the door stops moving entirely.

Which Therma-Tru Models This Applies To

Therma-Tru’s impact-rated garage door line spans a few core series, and the compatibility gotcha is real: door sections are not universal across series even when they look identical from the curb. The most common models we service in San Antonio are the Classic-Craft composite collection, the Pulse steel series, and the Smooth-Star fiberglass line. Each has its own panel profile, thickness spec, and hinge placement.

Here’s how to identify what you have without guessing. Look for a label on the inside of the door section, usually on the end stile or top rail. Therma-Tru stamps a serial number and series code there. If the label is unreadable, measure the panel thickness: Pulse steel panels run 2 inches thick, Classic-Craft composites run 1-3/4 inches, and Smooth-Star fiberglass doors are typically 2 inches as well. The hinge pattern matters too: Pulse uses a 14-gauge continuous hinge, Classic-Craft uses individual leaf hinges at 18-inch spacing. We keep OEM Therma-Tru panels and hardware for all three series in stock at our San Antonio location, which beats waiting 3 to 4 weeks for a special-order section.

When parts aren’t available OEM due to lead time, we offer quality aftermarket equivalents from our other stocked brands: PGT, CGI, and CWS all manufacture impact-rated replacement sections that match Therma-Tru’s specs on thickness and R-value. We’ll tell you upfront which route costs less and whether anything changes on the warranty side.

Signs Your Therma-Tru Impact Garage Door Is Failing

• Door shudders or hangs on one side during operation. This is almost always a worn roller or a hinge that’s pulled loose from the panel. On Therma-Tru doors, the bottom roller bracket takes the most abuse because San Antonio’s hard water leaves mineral deposits on the track that act like sandpaper.
• Visible rust bleeding from the bottom rail or lower panel seam. Impact-rated steel skins have a zinc coating, but once that coating is compromised by a scratch or a rock chip, rust spreads fast in our humidity. Composite and fiberglass panels don’t rust, but their steel end stiles can.
• The door doesn’t seal tight against the frame on one corner. This points to either a track that’s shifted out of square or a panel that’s slightly bowed. San Antonio’s clay soil expands and contracts with rain and drought, which slowly moves the concrete pad and throws door alignment off over time.
• You hear a popping or grinding sound near the spring assembly. A spring that’s about to snap gives warning. The noise means the coils are binding, usually from loss of lubrication or metal fatigue. Do not ignore this one, and do not stand under the spring while testing the door.
• Storm damage you can’t see from the inside. Impact-rated means the door should resist wind-borne debris without breaching, but the outer skin can take a dent that compromises the lamination underneath. If a hailstorm passed through San Antonio in the last year, have the door checked before hurricane season starts.

Replacement Cost & What’s Included

Here’s what a Therma-Tru impact garage door replacement costs in San Antonio, installed:

Every quote from Juniper Windows San Antonio includes the door sections, track, springs, rollers, hinges, weatherstripping, labor, haul-away of the old door, and a written line-item price before anything starts. The spread in price comes from door size, insulation package, and whether you’re matching an existing opener or replacing it too. Our workmanship warranty on garage door installs is 365 days, parts and labor, in writing, through the 365-Day Done Right Promise.

DIY or Call Us?

Here’s the honest split. You can safely inspect the tracks for debris, check the weatherstripping, and watch the door run one full cycle to see if it binds. You can also tighten visible hinge bolts with a socket wrench. That’s where the safe DIY list ends.

Do not attempt to replace torsion springs yourself. A garage door spring under tension holds enough stored energy to cause serious injury or death if it releases suddenly. The cables, the bottom bracket, and anything connected to the spring assembly are in the same category. For panel replacement, the weight and alignment make it a two-person job with the right experience; one wrong move and the panel jams in the track and bends. If you’re in San Antonio and the door isn’t opening smoothly right now, call us at (903) 488-7019 and we’ll send a background-checked technician. You’ll get a live arrival time before we show up, and the price is locked in writing before work begins.

FAQs